*The Dreambo圎dit will load the file and the window will be as follows: Now go into the menu bar and clik on (open) and search for the folder of BASE 22 MARS MOTEUR (the satellites services file), select it and tap OK. You can test your IP and your password if it works save this configuration in the end. Http port: 80 already configured on your router (tcp)įTP port 21 configured in your router also (tcp) IP Address IP address of your dream for me is 192.168.1.15 *it must be configured according to your network, clik on (optional) and a window opens: *Run Dreambo圎dit after downloading and decompression as mentioned above (# 1): This is an uncompressed file entitled "ENGINE BASED March 22" that contains several satellite (for satellite-powered) īut there is a simpler method using utility Dreambo圎dit provided you have a file and satellite bouquets borrowed from a friend. You can form bouquets, by using (Menu / Start a bouquet /) then select the channels to put in a specific bouquets, but it is a long and tiring. You can install using satellites (menu / configuration expert / search satellites) If your network is configured, you will see green and not red. clik on the button configuration copy the IP in the proper locations and in : You can now use Flashwizard to format your stick, format it and install a multiboot image (see above # 3) and you can use DCC to make sure that your network is configured: This is now your network is configured. *If everyone lost = 0 so it works, if not retry the process. Tick (Enable network) port 80 already configured on your router (tcp)Īnd press the button labeled green (save) and then reboot your dream.Īfter the start of your dream in the Start Menu (Run) (cmd) type at the prompt back Nameserver: the IP of your router (here: 192.168.1.1) In IP address to choose a form, x and y must be between 0 and 255. A window opens, select (Expert setup) then (communication setup) a window opens: Press the menu button on your remote, then with left scroll right button menu choose (setup), click on OK. The IP address of your router here: (192.168.1.1) It gives you an IP (Internet Protocol) to your PC here (192.168.1.10) Go to the Start menu, Run, type in (cmd) then in black window at the DOS prompt type in (ipconfig / all) *If you have a router, you must install to get at least connection on your PC. Wait several minutes for it to install the transponders and channels of Astra 19.2°, at the end tap OK and another window opens that asks if you want to scan another satellite, this time press the red button (not), choose a free channel to see if you succeeded or not. Here: choose the English language (you can later install an addon for the French)Ĭhoose Astra 19.2°, then transponder scan and finaly scan star. Your dream reboots, and windows will appear and where you need to answer: Make position engine on your satellite dish position satellite (eg Astra 19.2°) *For initial installation, use DreamUp, you don't need to network, and it is less risky than flaswizard (follow the instructions listed above # 2) Once the image is successfully installed, Open the yellow folder by double click, select the executable file and go in the menu bar of winrar, choose "Wizard" and follow the instructions DreamUp be unzipped into a new folder called DreamUp,ĭo the same thing with Flashwizard, dcc, Dreambo圎dit and the chosen image. Run winrar, then clik on a compressed file such as drumup (this site you can choose your gemini image depending on the version of your dreambox and other images that gemini). An image to install, I chose Gemini here: Gemini Images free Gemini Images, download Gemini Images, Gemini Images free download You have downloaded DreamUp, Flashwizard, Dreambo圎dit and DCC. * advice: when you set up your Dream save your image and save the DreamUp also with Flashwizard* It is now you need to configure your image in flash, satellite, network. Unplug the dreambox sector, and reconnect it. Click right button marked "flash" fetching official images or CVS LZMA compatible, and click ok. Connect the dream to the sector, the horizontal scroll bar is filled (from left to right). Local IP (PC) the address of your pc (for the address of your pc type in cmd to run the command: ipconfig /all) Disconect the dreambox sector and connect the cable RS232 of the dream to PC. for a first flash it is advisable to use instead of DreamUp Flashwizard it is a bit slow but it is more effective for the first time III-In this discussion, I shall gradually as explanations for beginners on how to use the Dreambox programs:
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |